PressureDependMultiYield-Example 8

From OpenSeesWiki
Jump to navigation Jump to search




Plastic Pressure Dependent Wet Level Dynamic


Input File

#Created by Zhaohui Yang (zhyang@ucsd.edu)
#plastic pressure dependent material
#plane strain,  single element,  dynamic analysis (input motion: sinusoidal acceleration at base)  
#SI units (m, s, KN, ton)
#
#         4     3
#         ------- 
#         |     |
#         |     |
#         |     |
#        1-------2   (nodes 1 and 2 fixed)
#         ^     ^
#          <--> input motion: sinusoidal acceleration at base
wipe
#
#some user defined variables
# 
set accMul   2          ;# acceleration multiplier
set massDen  2.0      ;# solid mass density
set fluidDen 1.0        ;# fluid mass density
set massProportionalDamping   0.0 ;
set stiffnessProportionalDamping 0.001 ;
set fangle 31.40         ;#friction angle
set ptangle 26.50        ;#phase transformation angle
set E      90000.0      ;#shear modulus
set poisson 0.40 ;
set G [expr $E/(2*(1+$poisson))] ;
set B [expr $E/(3*(1-2*$poisson))] ;
set press   0.0 ;# isotropic consolidation pressure on quad element(s)
set deltaT   0.010   ;# time step for analysis
set numSteps 2000   ;# Number of analysis steps
set gamma    0.600    ;# Newmark integration parameter
set period   1      ;# Period of applied sinusoidal load
set pi 3.1415926535     ;
set inclination 0       ;
set unitWeightX [expr  ($massDen-$fluidDen)*9.81*sin($inclination/180.0*$pi)] ;# unit weight in X direction
set unitWeightY [expr -($massDen-$fluidDen)*9.81*cos($inclination/180.0*$pi)] ;# unit weight in Y direction
#############################################################

#############################################################

#create the ModelBuilder
model basic -ndm 2 -ndf 2

# define material and properties
nDMaterial PressureDependMultiYield 2 2 $massDen $G $B  $fangle .1 80 0.5 \
                                        $ptangle 0.17 0.4 10  10 0.015 1.0
nDMaterial FluidSolidPorous 1 2 2 2.2D+6

    
# define the nodes
node 1   0.0D0 0.0D0 
node 2   1.0D0 0.0D0 
node 3   1.0D0 1.0D0 
node 4   0.0D0 1.0D0

# define the element      thick  material      maTag   press  density  gravity 
element quad  1  1 2 3 4  1.0   "PlaneStrain"     1   $press  0.0    $unitWeightX  $unitWeightY  

updateMaterialStage -material 2 -stage 0

# fix the base
fix 1 1 1 
fix 2 1 1

#tie nodes 3 and 4
equalDOF 3 4   1 2    

#############################################################
# GRAVITY APPLICATION (elastic behavior)
# create the SOE, ConstraintHandler, Integrator, Algorithm and Numberer
system ProfileSPD
test NormDispIncr 1.D-12 25 0
constraints Transformation
integrator LoadControl 1 1 1 1
algorithm Newton 
numberer RCM

# create the Analysis
analysis Static

#analyze 
analyze 2

# switch the material to plastic
updateMaterialStage -material 1 -stage 1
updateMaterialStage -material 2 -stage 1
updateMaterials -material 2 bulkModulus [expr $G*2/3.];

#analyze 
analyze 1

############################################################
# NOW APPLY LOADING SEQUENCE AND ANALYZE (plastic)

# rezero time
setTime 0.0
#loadConst -time 0.0D0
wipeAnalysis

pattern UniformExcitation 1 1 -accel "Sine 0 1000 $period -factor $accMul"

# create the Analysis
constraints Transformation; 
test NormDispIncr 1.D-6 25 0
algorithm Newton 
numberer RCM
system ProfileSPD
rayleigh $massProportionalDamping 0.0 $stiffnessProportionalDamping 0.
integrator Newmark $gamma  [expr pow($gamma+0.5, 2)/4]  
analysis VariableTransient 

recorder Node -file disp.out   -time  -node 1 2 3 4 -dof 1 2 -dT  0.01 disp
recorder Node -file acce.out  -time  -node 1 2 3 4 -dof 1 2 -dT 0.01 accel
recorder Element -ele 1 -time -file stress1.out -dT 0.01 material 1 stress 
recorder Element -ele 1 -time -file strain1.out -dT 0.01 material 1 strain 
recorder Element -ele 1 -time -file stress3.out -dT 0.01 material 3 stress 
recorder Element -ele 1 -time -file strain3.out -dT 0.01 material 3 strain 
recorder Element -ele 1 -time -file press1.out -dT 0.01 material 1 pressure 
recorder Element -ele 1 -time -file press3.out -dT 0.01 material 3 pressure 

#analyze 
set startT [clock seconds]
analyze $numSteps $deltaT [expr $deltaT/100] $deltaT 10
set endT [clock seconds]
puts "Execution time: [expr $endT-$startT] seconds."

wipe  #flush ouput stream


MATLAB Plotting File

clear all;

a1=load('acce.out');
d1=load('disp.out');
s1=load('stress1.out');
e1=load('strain1.out');
s5=load('stress3.out');
e5=load('strain3.out');
p1=load('press1.out');
p3=load('press3.out');

fs=[0., 0.2, 4, 6];
accMul = 2;

%integration point 1 p-q
po=(s1(:,2)+s1(:,3)+s1(:,4))/3;
for i=1:size(s1,1)
    qo(i)=(s1(i,2)-s1(i,3))^2 + (s1(i,3)-s1(i,4))^2 +(s1(i,2)-s1(i,4))^2 + 6.0* s1(i,5)^2;
    qo(i)=sign(s1(i,5))*1/3.0*qo(i)^0.5;
end
figure(1); clf;
%integration point 1 stress-strain
subplot(2,1,1), plot(e1(:,4),s1(:,5),'r');
title ('Integration point 1 shear stress \tau_x_y VS. shear strain \epsilon_x_y');
xLabel('Shear strain \epsilon_x_y');
yLabel('Shear stress \tau_x_y (kPa)');

subplot(2,1,2), plot(-po,qo,'r');
title ('Integration point 1 confinement p VS. deviatoric q relation');
xLabel('confinement p (kPa)');
yLabel('q (kPa)');
set(gcf,'paperposition',fs);
saveas(gcf,'SS_PQ1','jpg');

%integration point 3 p-q
po=(s5(:,2)+s5(:,3)+s5(:,4))/3;
for i=1:size(s5,1)
    qo(i)=(s5(i,2)-s5(i,3))^2 + (s5(i,3)-s5(i,4))^2 +(s5(i,2)-s5(i,4))^2 + 6.0* s5(i,5)^2;
    qo(i)=sign(s5(i,5))*1/3.0*qo(i)^0.5;
end

figure(4); clf;
%integration point 3 stress-strain
subplot(2,1,1), plot(e5(:,4),s5(:,5),'r');
title ('Integration point 3 shear stress \tau_x_y VS. shear strain \epsilon_x_y');
xLabel('Shear strain \epsilon_x_y');
yLabel('Shear stress \tau_x_y (kPa)');

subplot(2,1,2), plot(-po,qo,'r');
title ('Integration point 3 confinement p VS. deviatoric q relation');
xLabel('confinement p (kPa)');
yLabel('q (kPa)');
set(gcf,'paperposition',fs);
saveas(gcf,'SS_PQ5','jpg');

figure(2); clf;
%node 3 displacement relative to node 1
subplot(2,1,1),plot(d1(:,1),d1(:,6)*100,'r');
title ('Lateral displacement at element top');
xLabel('Time (s)');
yLabel('Displacement (cm)'); 
set(gcf,'paperposition',fs);
saveas(gcf,'D','jpg');


s=accMul*sin(0:pi/50:40*pi);
s1=interp1(0:0.01:20,s,a1(:,1));

figure(3); clf;
%node 3 relative acceleration
subplot(2,1,1),plot(a1(:,1),s1+a1(:,5),'r');
title ('Lateral acceleration at element top');
xLabel('Time (s)');
yLabel('Acceleration (m/s^2)');
set(gcf,'paperposition',fs);
saveas(gcf,'A','jpg');

figure(5); clf;
%integration point 1 excess pore water pressure
subplot(2,1,1),plot(p1(:,1),-p1(:,2),'r');
title ('Integration point 1 excess pore pressure');
xLabel('Time (s)');
yLabel('Excess pore pressure (kPa)');

subplot(2,1,2),plot(p1(:,1),p1(:,3),'r');
title ('Integration point 1 excess pore pressure ratio');
xLabel('Time (s)');
yLabel('Excess pore pressure ratio');
set(gcf,'paperposition',fs);
saveas(gcf,'EPWP','jpg');


Displacement Output File


Stress-Strain Output File

Excess Pore Pressure Output File


Acceleration Output File



Return to: