ZeroLengthImpact3D

• Command_Manual
  • Tcl Commands
  • Modeling_Commands
    • model
    • uniaxialMaterial
    • ndMaterial
    • frictionModel
    • section
    • geometricTransf
    • element
    • node
    • sp commands
      • fix
      • fixX
      • fixY
      • fixZ
    • mp commands
      • equalDOF
      • rigidDiaphragm
      • rigidLink
    • timeSeries
    • pattern
    • mass
    • block commands
      • block2D
      • block3D
    • region
    • rayleigh
  • Analysis Commands
    • constraints Command
    • numberer Command
    • system Command
    • test Command
    • algorithm Command
    • integrator Command
    • analysis Command
    • eigen Command
    • analyze Command
  • Output Commands
    • recorder
    • record
    • print
    • printA
    • logFile
    • RealTime_Output_Commands
  • Misc Commands
    • eleResponse Command
    • getTime Command
    • getEleTags Command
    • getNodeTags
    • loadConst Command
    • nodeCoord Command
    • nodeDisp Command
    • nodeVel Command
    • nodeAccel Command
    • nodeEigenvector Command
    • nodeBounds
    • print Command
    • remove Command
    • reset Command
    • testIter
    • testNorms
    • wipe Command
    • exit Command
  • DataBase Commands
    • Template:DataBaseCommandsMenu

---

This command constructs a node-to-node zero-length contact element in 3D space.

element zeroLengthImpact3D $tag $slaveNode $masterNode $direction $initGap $frictionRatio $Kt $Kn $Kn2 $Delta_y $cohesion

---

$tag	unique element object tag
$slaveNode	Slave node tag
$masterNode	Master node tag
$direction	1 if normal vector of master plane points to +X direction 2 if normal vector of master plane points to +Y direction 3 if normal vector of master plane points to +Z direction
$initGap	Initial gap between master plane and slave plane
$frictionRatio	Friction ratio
$Kt	Penalty in tangential directions (parallel to master and slave planes)
$Kn	Penalty in normal direction (normal to master and slave planes)
$Kn2	Penalty in normal direction after yielding based on Hertz impact model
$Delta_y	Yield deformation based on Hertz impact model
$cohesion	Cohesion, if no cohesion, it is zero

NOTES:

1. This element has been developed on top of the “zeroLengthContact3D”. All the notes available in “zeroLengthContact3D” wiki page would apply to this element as well. It includes the definition of master and slave nodes, the number of degrees of freedom in the domain, etc.
2. This element adds the capabilities of “ImpactMaterial” to “zeroLengthContact3D”, without the need for extra nodes and elements in the modeling process. That is the capability of having an "initial gap" in the normal direction and also the capability of considering energy dissipation due to impact in the normal direction.
3. This element has been used to model the superstructure-abutment interaction in bridges at University of Connecticut (UConn) and University of Nevada, Reno (UNR).

---

EXAMPLES:

wipe
source example.tcl
source gravityloads.tcl

---

REFERENCES:

Muthukumar, S., and DesRoches, R. (2006). “A Hertz Contact Model with Non-linear Damping for Pounding Simulation.” Earthquake Engineering and Structural Dynamics, 35, 811-828.

Muthukumar, S. (2003). “A Contact Element Approach with Hysteresis Damping for the Analysis and Design of Pounding in Bridges.” PhD Thesis, Georgia Institute of Technology. http://smartech.gatech.edu/

Nielson, B. (2005). “Analytical Fragility Curves for Highway Bridges in Moderate Seismic Zones.” PhD Thesis, Georgia Institute of Technology. http://smartech.gatech.edu/

---

Code Developed by: Arash E. Zaghi, Majid Cashany, University of Connecticut (UConn)